layout_edge_and_cutout module#

Keep copper back from the board edge, cutouts and holes with two rules.

Two builtin tags name the board’s openings, so these rules need no tag of your own:

  • IsBoardEdge is the outer edge of the board outline, and only that.

  • IsHole is every opening inside it. Measured on jitx 4.6, it matches a hole in the board outline polygon, a circuit Cutout (a routed slot) and a via’s drill. The drill of a plated through-hole pad was not tested.

design_constraint(IsBoardEdge, AnyObject).clearance(EDGE_CLEARANCE) keeps all copper 1.5 mm (EDGE_CLEARANCE) from the outer edge, and design_constraint(IsHole, AnyObject).clearance(HOLE_CLEARANCE) keeps it 0.5 mm (HOLE_CLEARANCE) from every opening. The board here has both kinds of inner opening: slot is a hole in CutoutBoard.shape, and cutout is a Cutout in the circuit. A GND pour larger than the board shows the pullback from each.

Measured on jitx 4.6, with a pour that reaches every feature:

  • The pour stops 1.51 mm from the outer edge, the edge rule plus 0.01 mm. Neither the outline slot nor the cutout follows the edge rule.

  • It stops 0.5 mm from the slot, from the cutout and from the drill of a via on another net (other_via here), each within 0.005 mm, measured from the drill, not the via pad.

  • The pour stays joined to gnd_anchor, its own net’s via. The hole pullback applies to the drills of other-net vias.

  • With neither rule, the pour stops 0.51 mm from the outer edge, the sample substrate’s min_copper_edge_space of 0.5 mm plus 0.01, and 0.206 mm from the slot and the cutout. min_copper_edge_space reaches only the outer edge too. The 0.206 mm at the slot and the cutout is just above the substrate’s min_copper_hole_space of 0.2032 mm; whether that floor sets it was not tested.

Because IsHole matches via drills, a hole rule wider than the via pad pulls copper back from other-net vias as well, and no second condition limits it to the board openings. A second condition narrows the other side of the rule: design_constraint(IsHole, IsPour) acts on pour copper only, and via drills still match it. Measured on jitx 4.6, under a 0.8 mm (IsHole, IsPour) rule in place of both rules here, the pour stopped 0.8 mm from the slot and the cutout and 0.8018 mm from another net’s via drill.

EDGE_CLEARANCE = 1.5#

Copper to the outer board edge, mm.

HOLE_CLEARANCE = 0.5#

Copper to any hole, slot or cutout, mm.

SLOT = [(9, -3), (11, -3), (11, 3), (9, 3)]#

A 2 mm by 6 mm slot in the board outline, centred at (10, 0).

class CutoutBoard[source]#

Bases: Board

A 40 mm by 30 mm board whose outline polygon has a slot in it.

shape: Shape = Polygon(elements=[(-20, -15), (20, -15), (20, 15), (-20, 15)], holes=[[(9, -3), (11, -3), (11, 3), (9, 3)]])#

The board outline shape.

class EdgeAndCutout[source]#

Bases: Circuit

A GND pour larger than the board, a routed cutout, and a via on another net, with the two clearance rules.

class layout_edge_and_cutout_design(*args, **kwargs)[source]#

Bases: Design

The pour, the cutout and the slotted board on the sample substrate.

board: Board = CutoutBoard()#
substrate: Substrate = SampleSubstrate()#
circuit: Circuit = EdgeAndCutout()#