network module#

The diplexer network: three edge-launch SMA jacks (Würth 60312202114514), two LQW15A inductors and six Accu-P capacitors.

Element order is the approved rough path’s; values stay in its part families. From the junction (J1 centre):

  • LOW arm: L1 series to node A; branch C3 at A; L2 series to node B; branch C4 at B; node B is J2’s centre.

  • HIGH arm: C1 series to node C; branch C5 at C; C2 series to node D; branch C6 at D; node D is J3’s centre.

Branch lines#

Each branch is a 0.20 mm printed line from its arm node to the hot pad of its tip capacitor, whose other pad goes to ground. The line is copper, not a part, so electrically it is a conductor of the arm node: the hot pad sits on the arm node’s own net (NODE_A, LOW, NODE_C, HIGH). The layout draws the line as a code Route on that net, from a RoutePoint on the arm line to the branch capacitor’s p1, tagged for its 0.20 mm width (jitx-code-layout). Each branch capacitor is its own field (c3 to c6), and its p1 is the stub tip, so the layout names the line’s end structurally.

A separate stub-tip net joined to the arm node would need an OverlappableCopper net tie and a VirtualConnection; the router ignores overlappable copper, so the line could not be a routed trace under the width and clearance rules, and the netlist would carry a short to explain.

Parts#

Every passive is a jitxlib.parts query against the jitxexamples catalogue (jitxexamples/parts/example-passives.csv). At every value used here the catalogue holds two Accu-P grades (P, +/-0.02 pF; Z, +/-0.01 pF) and a Murata GJM C0G part. The approved parts are Z grade, so each capacitor filters on manufacturer, the thin_film type and a relative tolerance no looser than +/-0.01 pF at its value: the CSV tolerance column is relative, so the bound is 0.01 pF over the capacitance. The inductors filter on Murata’s rf_wirewound type at G grade (+/-2 %).

ACCU_P = CapacitorQuery(manufacturer=Exactly(value='Kyocera AVX'), case=Exactly(value='0402'), extras=(('type', Exactly(value='thin_film')),))#

Kyocera AVX Accu-P 0402 thin-film capacitors (the approved part family).

ACCU_P_Z_GRADE_PF = 0.01#

//datasheets.kyocera-avx.com/accu-p.pdf), How to Order).

Type:

Accu-P tolerance code Z

Type:

+/-0.01 pF (Kyocera AVX Accu-P data sheet (https

LQW15A = InductorQuery(manufacturer=Exactly(value='Murata'), case=Exactly(value='0402'), extras=(('type', Exactly(value='rf_wirewound')),))#

Murata LQW15A 0402 wire-wound RF inductors (the approved part family).

LQW15A_G_GRADE = 0.02#

+/-2 % (Murata LQW15AN_80 reference specification JELF243A-0100).

Type:

LQW15A tolerance code G

accu_p_z(capacitance_pf)[source]#

An Accu-P 0402 capacitor of capacitance_pf picofarads at Z grade.

Return type:

Capacitor

Parameters:

capacitance_pf (float)

lqw15a_g(inductance_nh)[source]#

An LQW15A 0402 inductor of inductance_nh nanohenries at G grade.

Return type:

Inductor

Parameters:

inductance_nh (float)

class Diplexer[source]#

Bases: Circuit

The whole network with its three jacks. gnd is the ground return the top-level design names and pours.

gnd = Port()#
j1#

COMMON jack.

j2#

LOW jack.

j3#

HIGH jack.