power module#
Supply rails, straps and calibration resistors for the VP1002 and a Micron MT53E1G32D2FW LPDDR4 memory.
MemoryStraps names the memory’s two rails, VDD1 and the 1.1 V
net that joins VDD2 and VDDQ, ties its ODT_CA pins and holds its two ZQ
resistors. FpgaStraps makes the ties the cited documents require
of the FPGA (its paired supplies, its unused battery, eFUSE and
system-monitor pins) and holds its DCI reference resistor.
GtCalibration ties each transceiver calibration supply
to its AVTT rail and holds the transceivers’ RREF resistors. Each sits in
the circuit of the part it serves, so each rail is a net a regulator can
join. Rail voltages are left to the
regulator; the maxima here are the ones the decoupling ratings need.
The interface runs as LPDDR4, so the memory’s VDD2 and VDDQ and the VCCO of
XPIO banks 700 to 702 all run at 1.1 V (UG863 Table 23) and share one net,
MemoryStraps.LP4_1V1, which the base design joins to the three
VCCO rails. UG863 separates the SoC’s VCCO 1.1 V supply from the
memory’s VDDQ only when the memory must power down while the SoC stays
powered, which this design does not do. VDD1, 1.8 V, keeps its own net.
Sources#
Micron, LPDDR4X/LPDDR4 SDRAM data sheet,
z42m_embedded_lpddr4x_lpddr4.pdf, Rev. I, 04/2023, the copy the memory component cites: Table 5 “Ball/Pad Descriptions for x32”, “ZQ External Resistor, Tolerance, and Capacitive Loading” (page 196), Figure 3 “Dual-Die, Dual-Channel Package Block Diagram”, and Table 241 “Recommended DC Operating Conditions” in “LPDDR4 1.10V VDDQ”, the LPDDR4 rows.AMD UG863, Versal Adaptive SoC PCB Design User Guide, v1.12, 2026-06-16, https://docs.amd.com/r/en-US/ug863-versal-pcb-design: “Signals and Connections for LPDDR4/4x Interfaces”, Table 22 “LPDDR4/4x Signal Definitions” and Table 23 “Typical Supply Voltages for LPDDR4 and LPDDR4x”, with its note on separating the SoC’s VCCO from VDDQ; “IO_VR_700, IO_VR_800 Pin Differences”.
AMD AM010, Versal Adaptive SoC SelectIO Resources Architecture Manual, v1.7, 2025-05-22, https://docs.amd.com/r/en-US/am010-versal-selectio: “Calibrated Termination (Digitally Controlled Impedance)”.
AMD DS959, Versal Premium Series Data Sheet: DC and AC Switching Characteristics, v1.8, 2026-02-06, https://docs.amd.com/r/en-US/ds959-versal-premium: Table 1 “Recommended Operating Conditions”: the supply rows, and notes 4, 5, 6 and 8.
AMD AM006, Versal Adaptive SoC System Monitor Architecture Manual, v1.5, 2025-06-03, https://docs.amd.com/r/en-US/am006-versal-sysmon: Table 1 “SYSMON Package Pins” in “SYSMON Dedicated Pinout Requirements”, and Figure 1 “SYSMON Pinout Requirements” in “Analog Power Supply and Ground”.
AMD AM002, Versal Adaptive SoC GTY and GTYP Transceivers Architecture Manual, https://docs.amd.com/go/en-US/am002-versal-gty-transceivers, and AMD AM017, Versal Adaptive SoC GTM Transceivers Architecture Manual, https://docs.amd.com/go/en-US/am017-versal-gtm-transceivers: in each, “Termination Resistor Calibration Circuit”: the AVTTRCAL pin to the AVTT supply and to one pin of a 100 ohm precision resistor, the other pin to RREF, the two traces of the same length and geometry, under 0.5 ohm DC.
Trenz Electronic TE0950 schematic SCH-TE0950-03-MAKE21C, rev 03, 2023-12-19, https://shop.trenz-electronic.de/trenzdownloads/Trenz_Electronic/Development_Boards/TE0950/REV03/Documents/SCH-TE0950-03-MAKE21C.PDF, an XCVM1102 board, page 12 “V_GTY”: GTYP_AVTTRCAL_R (ball P6) on the GTYP_AVTT node, and R41, 100R 1%, from that node to GTYP_RREF_R (ball P7).
Not modeled: the system clock source, the RESET_n pull-down and CKE termination (UG863 Table 22: for LPDDR4, 160 ohm to GND and 160 ohm to VDD2), the rail voltages of the FPGA’s supplies, which depend on the speed grade (DS959 Table 1), the regulators’ remote sense on VCCINT_SENSE and GND_SENSE, and AM006’s two ferrite beads: the example catalogue has none, so VCCAUX_SMON joins VCCAUX_PMC and GND_SMON joins GND directly.
- VDD1_MAX = 1.95#
1.7, 1.8, 1.95 V.
- Type:
Memory VDD1 maximum,
V, LPDDR4. Micron Rev. I Table 241
- VDD2_MAX = 1.17#
1.06, 1.1, 1.17 V.
- Type:
Memory VDD2 maximum,
V, LPDDR4. Micron Rev. I Table 241
- VDDQ_MAX = 1.17#
1.06, 1.1, 1.17 V.
- Type:
Memory VDDQ maximum,
V, LPDDR4. Micron Rev. I Table 241
- VCCO_MAX = 1.575#
0.950 to 1.575 V. UG863 v1.12 Table 23 runs the controller’s banks at 1.1 V for LPDDR4, on the memory’s 1.1 V net. The banks’ capacitors are rated for this range maximum, not the memory’s 1.17 V, a design choice: it is the stricter rating, and it keeps the parts the banks had.
- Type:
XPIO VCCO maximum, V. DS959 v1.8 Table 1
- CORE_MAX = 0.906#
Maximum, V, of VCCINT, VCCINT_GT, VCC_IO, VCC_PMC, VCC_PSFP, VCC_PSLP, VCC_RAM and VCC_SOC: DS959 v1.8 Table 1, the high (H) voltage row of each, the highest of its rows.
- AUX_MAX = 1.545#
Maximum, V, of VCCAUX, VCCAUX_PMC, VCCAUX_SMON and the GTY and GTM AVCCAUX rails. DS959 v1.8 Table 1: 1.455, 1.500, 1.545 V.
- PSIO_VCCO_MAX = 3.4#
1.710 to 3.400 V.
- Type:
PSIO bank 5## VCCO maximum, V. DS959 v1.8 Table 1
- GTY_AVCC_MAX = 0.906#
0.854, 0.880, 0.906 V.
- Type:
GTY AVCC maximum, V. DS959 v1.8 Table 1
- GTM_AVCC_MAX = 0.948#
0.892, 0.920, 0.948 V.
- Type:
GTM AVCC maximum, V. DS959 v1.8 Table 1,
Eor I temperature range
- GT_AVTT_MAX = 1.236#
1.164, 1.200, 1.236 V.
- Type:
GTY and GTM AVTT maximum, V. DS959 v1.8 Table 1
- ZQ_RESISTANCE = 240.0#
ZQ calibration resistor, ohms, ZQ ball to VDDQ. Micron Rev. I Table 5 (ZQ0, ZQ1: “The ZQ pin shall be connected to VDDQ through a 240 ohm +/-1% resistor”) and page 196; UG863 v1.12 Table 22 (ZQ: 240 ohm to VDDQ).
- ZQ_TOLERANCE = 0.01#
“a 240 ohms, +/-1% tolerance external resistor must be connected between the ZQ pin and VDDQ”.
- Type:
ZQ resistor tolerance, +/-1%. Micron Rev. I page 196
- RREF_RESISTANCE = 100.0#
Transceiver RREF resistor, ohms, from the AVTT rail to the RREF ball. AM002 and AM017, “Termination Resistor Calibration Circuit”: 100 ohm precision; TE0950 rev 03 page 12, R41: 100R.
- RREF_TOLERANCE = 0.01#
1%.
- Type:
TE0950 rev 03 page 12, R41
- IO_VR_RESISTANCE = 240.0#
DCI reference resistor, ohms, IO_VR_700 to VCCO_700. UG863 v1.12 Table 22 (IO_VR_7xx: 240 ohm to VCCO_7xx); AM010 v1.7, “Calibrated Termination”: “Banks with IO_VR pins must have an external 240 ohm resistor tied to the bank’s VCCO”, in every design. Neither gives a tolerance, so the query pins none.
- class MemoryStraps(memory)[source]#
Bases:
ContainerThe memory’s rails as named nets, VDD1 and the 1.1 V net of VDD2 and VDDQ, its ODT_CA straps and its two ZQ resistors.
One ZQ resistor per ZQ ball. The dual-die part has one ZQ ball per die (Micron Rev. I Figure 3: ZQ0 on the die selected by CS0, ZQ1 on the die selected by CS1), and Table 5 ties each ZQ pin to VDDQ through its own 240 ohm. Page 196 allows two ranks to share one resistor only if the controller keeps their ZQ calibrations from overlapping; separate resistors leave the controller free of that rule.
- Parameters:
memory (MT53E1G32D2FW_046_WT_B)
- class FpgaStraps(fpga)[source]#
Bases:
ContainerThe ties the vendors require of the FPGA’s supplies and pins, and its DCI reference resistor.
The FPGA’s rails are already named nets with a
Powerport each onVP1002LPDDR4; a regulator joins one at itsVp.- Parameters:
fpga (VP1002LPDDR4)
- class GtCalibration(fpga)[source]#
Bases:
ContainerEach transceiver group’s calibration supply and reference resistor.
AM002 (GTY) and AM017 (GTM), “Termination Resistor Calibration Circuit”, connect the AVTTRCAL pin to the group’s AVTT supply and to one pin of a 100 ohm precision resistor, and the resistor’s other pin to RREF. Each group here does that on its own AVTT rail, so the AVTT capacitors decouple AVTTRCAL too. TE0950 rev 03 page 12 builds the same circuit for GTYP with R41, 100R 1%, the tolerance used here. DS959 v1.8 Table 1 lists the GTY and GTM AVTTRCAL supplies with the same range as AVTT, 1.164 to 1.236 V.
- Parameters:
fpga (VP1002LPDDR4)