Source code for jitxlib.jlcpcb.JLC02076_RO4350B
from jitx.container import inline
from jitx.stackup import Stackup
from jitxlib.physics import phase_velocity
from .materials import (
Copper1oz,
Df_RO4350B,
RO4350B_Core762,
SoldermaskMaterial,
)
from .rules import JLCPCBRogersRules
from .substrate import (
SOLDERMASK,
JLCPCBSubstrate,
Trace,
single_ended,
symmetric,
)
from .vias import UnfilledVias
# Effective permittivity of the 50 ohm line below, from the same field solve
# as its width and gap.
eeff_50 = 2.547
[docs]
class JLC02076_RO4350B(JLCPCBSubstrate, UnfilledVias):
"""2-layer Rogers RO4350B, 0.762 mm laminate, 1 oz copper.
Ordered as base material Rogers, laminate RO4350B, PCB thickness 0.76 mm.
JLCPCB gives the finished board as 0.9 mm. Surface finish is ENIG or OSP;
HASL is not offered on Rogers.
"""
@inline
class stackup(Stackup):
"""2 layer stackup on a 0.762 mm RO4350B laminate"""
layers = symmetric(
SoldermaskMaterial(thickness=SOLDERMASK),
Copper1oz(),
centre=RO4350B_Core762(),
)
constraints = JLCPCBRogersRules()
# Grounded coplanar waveguide: the trace with ground pour on both sides
# at `clearance`, over the ground plane on the other face. Microstrip on
# this laminate would be wider than a 0402 pad.
#
# Width and gap: the 50 ohm line should land on a 0402 pad (about 0.5 mm
# wide) without a large step, so the width is as close to 0.55 mm as a
# gap of 0.12 mm or more allows (0.02 mm above the 0.10 mm minimum space,
# in 0.01 mm steps), and never under 0.50 mm. On this laminate a
# 0.12 mm gap gives 0.52 mm and 0.13 mm gives 0.57 mm, the closer of the
# two.
#
# Solved by `gcpw` in tests/test_stackups.py, which TestGroundedCoplanar
# runs: a 2D quasi-static finite-difference solve of the cross-section as
# built, with Dk 3.66, 35 um copper and JLCPCB's soldermask coating
# (0.6 mil over the trace, 1.2 mil in the gap, Dk 3.8). It gives 50.0 ohm.
# JLCPCB's etch moves the edges: a gap 0.02 mm narrower or wider moves
# the line by -2.79 or +2.45 ohm, a width 0.02 mm narrower or wider by
# +0.53 or -0.50 ohm. The soldermask is worth about 3.6 ohm: opened over
# the line, the solve gives 53.6 ohm.
#
# The pour must sit at exactly the 0.13 mm gap. `clearance` is a minimum,
# so a board-level clearance rule above it widens the gap: at 0.20 mm the
# line is 57.5 ohm.
# The solve also holds that pour at the bottom plane's potential, so it
# must be stitched to the bottom plane with vias along the line.
RS_50 = single_ended(
50,
{0: Trace(trace_width=0.57, clearance=0.13, velocity=phase_velocity(eeff_50))},
insertion_loss=Df_RO4350B,
)